|
Joined: Oct 2013
Posts: 2,264
Campfire Regular
|
OP
Campfire Regular
Joined: Oct 2013
Posts: 2,264 |
If any of you are experienced plumbers or have dealt with or who have worked on old plumbing fixtures and sinks could use some help The bottom drain cast iron piece, is it part of the sink as in all one piece or does it come off? Not talking about the flange with the two nuts. Obviously that comes off
|
|
|
|
Joined: Aug 2010
Posts: 28,035
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2010
Posts: 28,035 |
That’s a cool sink. Surely that piece comes off.
|
|
|
|
Joined: Jan 2010
Posts: 23,540
Campfire Ranger
|
Campfire Ranger
Joined: Jan 2010
Posts: 23,540 |
does the top drain piece(s) pictured in the sink screw out?
I don't know what its called. Where you put the stopper.
Last edited by KFWA; 12/12/22.
have you paid your dues, can you moan the blues, can you bend them guitar strings
|
|
|
|
Joined: May 2003
Posts: 16,971
Campfire Ranger
|
Campfire Ranger
Joined: May 2003
Posts: 16,971 |
You need a tool that goes into the drain from the top on each side that unscrews that brass coupling from the bottom part…
Then you can’t put new drain’s in each side and use modern plumbing for it.
If those are stuck. You can always cut the bottom section off, and or grind it off to separate them.
they have the tool at any hardware store, basically it’s got 2 cuts across the bottom that fit into the drain piece (if it’s a tub type drain ).. if it’s a sick drank they it’s going to be tuffer becaus you have to just unscrew them…. You COULD always take a Dremel cutting tool and cut the inside flange off the top pieces by cutting inside the drain tube, but you’d have to do it just below the lip because if you cut too far down you’ll have to cut the steep insert to get to the brass first.
Last edited by Spotshooter; 12/12/22.
|
|
|
|
Joined: Oct 2013
Posts: 2,264
Campfire Regular
|
OP
Campfire Regular
Joined: Oct 2013
Posts: 2,264 |
Not sure if the top drain piece comes out or not . Trying to buy it for our new house build!
If you notice the center sink divider has a drain hole for Overflow as well which would probably be independent of the other two plumbing wise
Okay. So spotshooter the top drain pieces screw out and the bottom flange will come off. Then I can plumb with whatever size it ends up being. I think it’s 1.5” plumbing on this old sink. Any idea what the tool is I need to remove those pieces?!
|
|
|
|
Joined: Oct 2013
Posts: 2,264
Campfire Regular
|
OP
Campfire Regular
Joined: Oct 2013
Posts: 2,264 |
Sorry. Our timing was on. You answered my question !
Thanks
|
|
|
|
Joined: Jan 2010
Posts: 8,007
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2010
Posts: 8,007 |
Strainer baskets are probably threaded into that rusted out connector. With any luck the threads are solid brass, so hopefully not totally rust welded together. You might be able to crack that cast iron part with some careful whacks with a hammer or hammer and cold chisel. But, the sink is probably cast as well, so that would risk cracking the sink body. Sawzall with a cast iron blade, but that isn't really the most fun.
|
|
|
|
Joined: Feb 2019
Posts: 158
Campfire Member
|
Campfire Member
Joined: Feb 2019
Posts: 158 |
Leave everything be and use a Fernco coupling. Neal
|
|
|
|
Joined: Feb 2013
Posts: 21,777
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2013
Posts: 21,777 |
Personally I would not disassemble anything.
Can of worms...
Buy or fabricated a transition from the old drain pipe and go new from there.
Gelcoat the drains inside the sink any color you like.
Nice old sink.
If you are not actively engaging EVERY enemy you encounter... you are allowing another to fight for you... and that is cowardice... plain and simple.
|
|
|
|
Joined: Feb 2013
Posts: 21,777
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2013
Posts: 21,777 |
Leave everything be and use a Fernco coupling. Neal Fernco...
If you are not actively engaging EVERY enemy you encounter... you are allowing another to fight for you... and that is cowardice... plain and simple.
|
|
|
|
Joined: Jan 2010
Posts: 23,540
Campfire Ranger
|
Campfire Ranger
Joined: Jan 2010
Posts: 23,540 |
Personally I would not disassemble anything.
Can of worms...
Buy or fabricated a transition from the old drain pipe and go new from there.
Gelcoat the drains inside the sink any color you like.
Nice old sink. probably a good idea, maybe a rubber coupling with two clamps on it is that what a Fernco is? I've never heard it called that
Last edited by KFWA; 12/12/22.
have you paid your dues, can you moan the blues, can you bend them guitar strings
|
|
|
|
Joined: Jun 2001
Posts: 19,080
Campfire Ranger
|
Campfire Ranger
Joined: Jun 2001
Posts: 19,080 |
You are in for a lot off frustration. I would buy some cut off disk for you smaller grinder and go to work cutting everything. It is my guess, that silver piece is installed into the cast iron piece like a standard sink and you have to get the two square nuts off to get it out The studs are probably threaded in to the casting,but severely rusted. The drain rings in the sink itself are probably threaded into the casting with plumber's putty applied to the bottom drain ring. Getting every thing will be the hard part. Don't know if you can find a dual sink drain with outlets that close, you might have to use PVC an design your own. Or just buy a rubber coupling and attach to that bottom silver piece after cleaning it up. Home Depot shows these. https://www.homedepot.com/p/SIMPLE-...uLoBwKDoUxoCulwQAvD_BwE&gclsrc=aw.ds
Last edited by saddlesore; 12/12/22.
If God wanted you to walk and carry things on your back, He would not have invented stirrups and pack saddles
|
|
|
|
Joined: Feb 2019
Posts: 158
Campfire Member
|
Campfire Member
Joined: Feb 2019
Posts: 158 |
Fernco is a rubber coupling with either 2 or 4 hose clamps and come in many different sizes. Fernco is a brand name. I wish I knew how to post pics. Neal
|
|
|
|
Joined: Oct 2013
Posts: 2,264
Campfire Regular
|
OP
Campfire Regular
Joined: Oct 2013
Posts: 2,264 |
If I can get everything off and need to reuse the bottom piece I can have the uncle who owns metal finishing business get rust off and zinc plate for free
I’m not opposed to leaving as is and fixing the leak and the bottom flange where the two nuts are. It held water for 5 days and that area had some leaking.
I would just prefer to fix it now before it’s installed. Easier for sure
|
|
|
|
Joined: Dec 2004
Posts: 9,743
Campfire Outfitter
|
Campfire Outfitter
Joined: Dec 2004
Posts: 9,743 |
Yep, if your going to restore go all the way.
Use the original parts, that cast piece would clean up well, powder coat it or just a high quality primer and paint.
|
|
|
|
Joined: Jan 2006
Posts: 69,360
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2006
Posts: 69,360 |
That overflow can be a problem. I'm guessing there's some kind of hole with a gasket in the top of the cast iron that it drains into. Finding an aftermarket piece for it could be difficult at best.
“In a time of deceit telling the truth is a revolutionary act.” ― George Orwell
It's not over when you lose. It's over when you quit.
|
|
|
|
Joined: Jan 2001
Posts: 14,313
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2001
Posts: 14,313 |
As one has already said, leave it alone and use the Fernco Coupling if possible. Before placing it in its location, set it up outside using a Fernco Coupling and the end capped off, fill the tub with water and let it sit to see if it leaks.
Phil
|
|
|
|
Joined: Apr 2011
Posts: 151,367
Campfire Savant
|
Campfire Savant
Joined: Apr 2011
Posts: 151,367 |
I’ve never seen one like that, bottom slip joint will come off. Why can’t you connect there with new brass or plastic slip nut fitting?
|
|
|
|
Joined: Oct 2013
Posts: 2,264
Campfire Regular
|
OP
Campfire Regular
Joined: Oct 2013
Posts: 2,264 |
I’m sure I can connect to the bottom tail piece with a slip
But once installed will be much harder to repair any issues down the road. It weighs 337lbs so not taking in and out would be ideal. So restoring that now would be advantageous
Don’t plan on restoring the enamel other than fixing the two chips.
Jeff. Thanks for the info!!
|
|
|
|
324 members (257_X_50, 1_deuce, 10gaugemag, 2500HD, 260Remguy, 39 invisible),
2,369
guests, and
1,206
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,860
Posts18,478,571
Members73,948
|
Most Online11,491 Jul 7th, 2023
|
|
|
|