|
Joined: Sep 2018
Posts: 1,188
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2018
Posts: 1,188 |
This happened today. I will add a few more pics and info...on my phone so 1 at a time it will be!
......the occasional hunter wielding a hopelessly inaccurate rifle, living by the fantastical rule that this cartridge can deliver the goods, regardless of shot placement or rifle accuracy. The correct term for this is minute of ego.
|
|
|
|
Joined: Sep 2018
Posts: 1,188
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2018
Posts: 1,188 |
Saved the chip. Measured with a calipers it is .2 deep
......the occasional hunter wielding a hopelessly inaccurate rifle, living by the fantastical rule that this cartridge can deliver the goods, regardless of shot placement or rifle accuracy. The correct term for this is minute of ego.
|
|
|
|
Joined: Sep 2018
Posts: 1,188
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2018
Posts: 1,188 |
So I had the rifle bedded, just picked it up today. There was a crack there before, I was hoping the bedding would help relieve the recoil. So a few questions, is this repairable? I am an amateur woodworker so I am not afraid to glue the chip back in. I am just afraid if it happened once it may happen again? This stock is on a BRNO Mauser, and obviously came from a different rifle. Chambering is 338-06, so has some recoil. Or would you just scrap the stock? I got the gun for 325, so I am not opposed to putting it in a Boyds.
......the occasional hunter wielding a hopelessly inaccurate rifle, living by the fantastical rule that this cartridge can deliver the goods, regardless of shot placement or rifle accuracy. The correct term for this is minute of ego.
|
|
|
|
Joined: Jun 2001
Posts: 296
Campfire Member
|
Campfire Member
Joined: Jun 2001
Posts: 296 |
Totally repairable. Use Acraglass -- the thin stuff rather than the gel.
|
|
|
|
Joined: Jan 2001
Posts: 7,988 Likes: 3
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2001
Posts: 7,988 Likes: 3 |
Easy fix. I would use Elmers Titebond, clamp it sufficiently to not squeeze out all the glue, let it dry. Sand any small imperfections lightly . Take the action out of the rifle and relieve the wood a bit at the point so the action isn't driven back into it in recoil
Never underestimate your ability to overestimate your ability.
|
|
|
|
Joined: Jun 2001
Posts: 19,091 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Jun 2001
Posts: 19,091 Likes: 2 |
Easy fix. I would use Elmers Titebond, clamp it sufficiently to not squeeze out all the glue, let it dry. Sand any small imperfections lightly . Take the action out of the rifle and relieve the wood a bit at the point so the action isn't driven back into it in recoil Exactly!!!!!
If God wanted you to walk and carry things on your back, He would not have invented stirrups and pack saddles
|
|
|
|
Joined: Jul 2012
Posts: 646
Campfire Regular
|
Campfire Regular
Joined: Jul 2012
Posts: 646 |
|
|
|
|
Joined: Feb 2001
Posts: 50,643 Likes: 1
Campfire Kahuna
|
Campfire Kahuna
Joined: Feb 2001
Posts: 50,643 Likes: 1 |
I agree on the easy fix and relieving behind the tang... but it is really important IMO to bed it properly. That is a bedding issue.
And I would not use anything but epoxy. There is more than enough oil in the wood to cause problems and therefore I would use the best glue. I have zero problem using Elmer's Titebond on fresh clean wood.
Mark Begich, Joaquin Jackson, and Heller resistance... Three huge reasons to worry about the NRA.
|
|
|
|
Joined: Jul 2011
Posts: 11,057
Campfire Outfitter
|
Campfire Outfitter
Joined: Jul 2011
Posts: 11,057 |
Easy fix. I would use Elmers Titebond, clamp it sufficiently to not squeeze out all the glue, let it dry. Sand any small imperfections lightly . Take the action out of the rifle and relieve the wood a bit at the point so the action isn't driven back into it in recoil Except use epoxy, not white glue.
"There's more to optics than meets the eye."--anon
"...most of us would be better off losing half a pound around the waist than half a pound on our rifle."--dhg
|
|
|
|
Joined: Jul 2005
Posts: 6,800
Campfire Tracker
|
Campfire Tracker
Joined: Jul 2005
Posts: 6,800 |
Old Corps
Semper Fi
FJB
|
|
|
|
Joined: Sep 2014
Posts: 21,864 Likes: 5
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2014
Posts: 21,864 Likes: 5 |
#1. Fire the Ten Thumbed POS who calls himself a ................... I just can't even say gun smith thinking about your bedding job!
How can anyone have bedded that gun and not addressed the problem. Especially not relieved the tang on a Mauser?
Do not take it to him.
PS. Not a Smith myself. Just a DIY hack.
Parents who say they have good kids..Usually don't!
|
|
|
|
Joined: Sep 2011
Posts: 1,966
Campfire Regular
|
Campfire Regular
Joined: Sep 2011
Posts: 1,966 |
Use a good 2-part, clear, medium to slow cure epoxy - not Marine Tex or steel bed or any other bedding material. The epoxy is much more viscous and will flow and fill every crevice, penetrate into the pores of the wood.
Make sure the stock and chip bare wood areas are cleaned well with lacquer thinner. Let dry and repeat. Let dry and then drill some small holes in the stock first - and if possible a couple in the chip - liberally apply epoxy to both, using toothpick ensure the holes are filled - press fit together wiping the excess off with a rag dampened with lacquer thinner to clean off excess epoxy. Tightly wrap several times around with masking tape and do not touch it until completely CURED.
AKA The P-Man If you cherish your memories with kids, be a good role model . . . . so the RIGHT memories of you mean something to them.
|
|
|
|
Joined: Jan 2003
Posts: 3,453 Likes: 8
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2003
Posts: 3,453 Likes: 8 |
Use a good 2-part, clear, medium to slow cure epoxy - not Marine Tex or steel bed or any other bedding material. The epoxy is much more viscous and will flow and fill every crevice, penetrate into the pores of the wood.
Make sure the stock and chip bare wood areas are cleaned well with lacquer thinner. Let dry and repeat. Let dry and then drill some small holes in the stock first - and if possible a couple in the chip - liberally apply epoxy to both, using toothpick ensure the holes are filled - press fit together wiping the excess off with a rag dampened with lacquer thinner to clean off excess epoxy. Tightly wrap several times around with masking tape and do not touch it until completely CURED. The above is the best fix. The tang shouldn't have any contact with the stock or the same thing will happen again. The back of the recoil lug is what should be taking the load...nothing else. Good shootin' -Al
Forbidden Zoner
|
|
|
|
Joined: Jan 2001
Posts: 59,177 Likes: 3
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2001
Posts: 59,177 Likes: 3 |
Totally repairable. Use Acraglass -- the thin stuff rather than the gel. Failing that, use a good 2-ton epoxy - clamped tight for 24-36 hours.. I would also 'pin' it as well, after the epoxy is fully set.. The two pin sizes I used was 3/32 or 1/8"... I'd use the latter for your stock... YMMV...
Ex- USN (SS) '66-'69 Pro-Constitution. LET'S GO BRANDON!!!
|
|
|
|
Joined: Feb 2016
Posts: 17,831
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2016
Posts: 17,831 |
Common deal. Easy fix and then back to shootin.
|
|
|
|
Joined: Sep 2018
Posts: 1,188
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2018
Posts: 1,188 |
Thanks guys! Got some 2 ton epoxy and will repair with that
......the occasional hunter wielding a hopelessly inaccurate rifle, living by the fantastical rule that this cartridge can deliver the goods, regardless of shot placement or rifle accuracy. The correct term for this is minute of ego.
|
|
|
|
Joined: Jan 2003
Posts: 3,453 Likes: 8
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2003
Posts: 3,453 Likes: 8 |
If the epoxy you choose seems a bit thick, warming it with a hair dryer can help. -Al
Forbidden Zoner
|
|
|
|
Joined: Jan 2001
Posts: 7,988 Likes: 3
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2001
Posts: 7,988 Likes: 3 |
You're probably right about that, but I use Elmer's woodworking glue and Titebond pretty much interchangeably in my woodworking projects. Both are excellent... I use them on a lot of stock repairs also, but in this case if the wood isn't fresh and clean the epoxy is the better material as has been stated... Bob
Never underestimate your ability to overestimate your ability.
|
|
|
|
Joined: Sep 2010
Posts: 7,476 Likes: 6
Campfire Tracker
|
Campfire Tracker
Joined: Sep 2010
Posts: 7,476 Likes: 6 |
Medics bury their mistakes..
|
|
|
|
Joined: Jul 2011
Posts: 11,057
Campfire Outfitter
|
Campfire Outfitter
Joined: Jul 2011
Posts: 11,057 |
Because you want a permanent repair.
"There's more to optics than meets the eye."--anon
"...most of us would be better off losing half a pound around the waist than half a pound on our rifle."--dhg
|
|
|
|
405 members (16gage, 12savage, 10gaugeman, 10Glocks, 10gaugemag, 160user, 46 invisible),
2,134
guests, and
1,117
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,859
Posts18,497,130
Members73,979
|
Most Online11,491 Jul 7th, 2023
|
|
|
|