|
|
Joined: Mar 2003
Posts: 643
Campfire Regular
|
OP
Campfire Regular
Joined: Mar 2003
Posts: 643 |
I recently picked up an unfired REM 700 XCR II and when I removed the base screw plugs I noticed the front hole (over the chamber) is blind.
I am only able to get 2 1/2 turns with any base/screw combo before it bottoms out.
I’ve owned well over 50 Rem 700’s and they all have been tapped clear through so you could see the barrel threads.
This one has a nice clean flat bottom (looks factory finished) but as mentioned is only a few threads deep.
Anybody encountered this?
May explain why it was unfired lol.
Last edited by 280_ACKLEY; 07/07/23.
"You miss 100% of the shots you don't take!"
|
|
|
|
Joined: Jul 2003
Posts: 5,771
Campfire Tracker
|
Campfire Tracker
Joined: Jul 2003
Posts: 5,771 |
I have owned well over 50 Rem 700s. All have have been tapped clear through - so one could see the barrel threads.
In my experiance, what you have is NOT the norm.
GB
|
|
|
|
Joined: Nov 2004
Posts: 17,775 Likes: 29
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2004
Posts: 17,775 Likes: 29 |
Do the base screws tighten or are they too long for that hole?
"I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man." Thomas Jefferson
GeoW, The "Unwoke" Clean up on aisle 46! "A Well Regulated Militia" Life Member
|
|
|
|
Joined: Mar 2003
Posts: 643
Campfire Regular
|
OP
Campfire Regular
Joined: Mar 2003
Posts: 643 |
Do the base screws tighten or are they too long for that hole? The other three are all good, but the front screw is far too loose with any of the standard screws supplied with any of my variety of bases. Went through all my old screws and found the shortest screw imaginable, and it’ll just start to snug up when it bottoms out (at ~ 2 1/2 revs)
"You miss 100% of the shots you don't take!"
|
|
|
|
Joined: Nov 2004
Posts: 17,775 Likes: 29
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2004
Posts: 17,775 Likes: 29 |
I've seen bases that use one long screw and one short one and was thinking that perhaps that is what was going on. Hope it get straightened out for you.
"I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man." Thomas Jefferson
GeoW, The "Unwoke" Clean up on aisle 46! "A Well Regulated Militia" Life Member
|
|
|
|
Joined: Nov 2019
Posts: 3,906 Likes: 31
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2019
Posts: 3,906 Likes: 31 |
I've seen bases that use one long screw and one short one and was thinking that perhaps that is what was going on. Hope it get straightened out for you. Isn’t that because of the thickness of the base rather than varying tap depth in the receiver?
|
|
|
|
Joined: Mar 2003
Posts: 643
Campfire Regular
|
OP
Campfire Regular
Joined: Mar 2003
Posts: 643 |
Thanks for the replies
Thinking at this point I’ll have my smith pull the barrel and drill and tap it.
I just can’t imagine Big Green using a blind hole, so hopefully it’s not a broken tap in there.
"You miss 100% of the shots you don't take!"
|
|
|
|
Joined: Nov 2004
Posts: 17,775 Likes: 29
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2004
Posts: 17,775 Likes: 29 |
I've seen bases that use one long screw and one short one and was thinking that perhaps that is what was going on. Hope it get straightened out for you. Isn’t that because of the thickness of the base rather than varying tap depth in the receiver? This is what I was thinking... Link
"I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man." Thomas Jefferson
GeoW, The "Unwoke" Clean up on aisle 46! "A Well Regulated Militia" Life Member
|
|
|
|
Joined: Jul 2003
Posts: 5,771
Campfire Tracker
|
Campfire Tracker
Joined: Jul 2003
Posts: 5,771 |
I've seen bases that use one long screw and one short one and was thinking that perhaps that is what was going on. Hope it get straightened out for you. Isn’t that because of the thickness of the base rather than varying tap depth in the receiver? This is what I was thinking... LinkNo. According to the OP - the front hole of the receiver is "blind" - it was not drilled all the way through the action. That is the issue. Not the base or length of the screw.
|
|
|
|
Joined: Aug 2010
Posts: 33,811 Likes: 182
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Aug 2010
Posts: 33,811 Likes: 182 |
The people walking in darkness have seen a great light Isaiah 9:2
|
|
|
|
Joined: Dec 2016
Posts: 6,410 Likes: 70
Campfire Tracker
|
Campfire Tracker
Joined: Dec 2016
Posts: 6,410 Likes: 70 |
I've had to file/grind more than one of those front screws to get it to fit and tighten correctly. But, as you said, you could see the barrel threads through the hole, not a blind hole. I would suggest a competent gunsmith and possible have the 4 holes D&T for 8-40 screws instead of the 6-40 they are now.
It isn't what happens to you that defines you, it's what you DO about what happens to you that defines you!
NRA life member
Illinois State Rifle Association member
|
|
|
|
Joined: Aug 2014
Posts: 6
New Member
|
New Member
Joined: Aug 2014
Posts: 6 |
You might just try the short screw you mentioned and put a small washer in the base slot, just a thought
|
|
|
|
179 members (30Gibbs, 2ndwind, 308xray, 300_savage, 19352012, 1911a1, 28 invisible),
22,812
guests, and
616
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums82
Topics1,219,641
Posts19,038,802
Members74,743
|
Most Online26,902 Nov 28th, 2024
|
|
|
|
|