|
Joined: Jul 2009
Posts: 300
Campfire Member
|
OP
Campfire Member
Joined: Jul 2009
Posts: 300 |
Howdy folks. I recently began work with my first ever long range rig, its a Zastava Mark X in 6.5-284, 27 3/4 inch benchmark barrel, fluted, leupold 6.5-20 on top of it, in a boyds laminate stock, actually a pretty sharp looking piece. Anyway, I have been doing all of my development at 350 yds, and have a horizontal stringing issue. all bullets land within about 1 to 1 1/2 inches of each other vertically speaking at that distance, but horizontal is more like 4 inches or so, Any advice on how to fix this? bedding maybe?, how would I check?
Thanks Nick
|
|
|
|
Joined: Jun 2001
Posts: 19,106 Likes: 5
Campfire Ranger
|
Campfire Ranger
Joined: Jun 2001
Posts: 19,106 Likes: 5 |
I'd suggest it's bedding if it is not shooting technique
If God wanted you to walk and carry things on your back, He would not have invented stirrups and pack saddles
|
|
|
|
Joined: Dec 2012
Posts: 16
New Member
|
New Member
Joined: Dec 2012
Posts: 16 |
The big question is How much wind was present? Even a mild breeze will widen the group at that distance
|
|
|
|
Joined: Jul 2009
Posts: 300
Campfire Member
|
OP
Campfire Member
Joined: Jul 2009
Posts: 300 |
breeze was off and on maybe 3mph, but no more than that. I thought maybe shooting technique as well, but ruled that out by dropping 5 into about 2/3 at 100 with the .358 Yukon on the same day. I dont feel that I am recoil shy or anything like that, its a pretty mild recoiling rig, it has a longer than stanard firing pin travel, its even longer than a normal mauser, could this cause some horizontal, I dry fired it while looking through the scope at the target at that distance, and it doesnt appear to shake to that extent. Is there some way to shim the sides of the recoil lug to take up that space, or do I need to dremel some of the bedding out, and try again?
Last edited by RugerDude; 08/04/13.
|
|
|
|
Joined: Mar 2009
Posts: 2,804 Likes: 1
Campfire Regular
|
Campfire Regular
Joined: Mar 2009
Posts: 2,804 Likes: 1 |
I had a 30'06 that once bedded went from large groups to stringing them. I talked to a smith and he suggested a folded business card between the barrel and tip of the forend. Stringing went away. He bedded the last 2" of the barrel channel and fixed the issue completely.
I have used the folded card trick anytime I see it and 90% it cures it for the sub $1000 production rifles.
NRA Endowed Patron Life Benefactor GOA Life Member TSRA Life Member NSCA Life Member
|
|
|
|
Joined: Feb 2008
Posts: 1,267
Campfire Regular
|
Campfire Regular
Joined: Feb 2008
Posts: 1,267 |
Is there some way to shim the sides of the recoil lug to take up that space, or do I need to dremel some of the bedding out, and try again?
I bought a used rifle that shot like that (VERY inexpensively). I would suggest you get some Play-Dough & roll a few thin spaghetti-like strands to place at various places in the bedding to determine exactly what's up & where. Mauser's usually shoot best with the rifle's metal touching the bedding ONLY at the rear face of the recoil lug (never at the sides or bottom), the bottom of the action flat to the rear of the lug, the underside of the rear tang (the rear tang face should have clearance from the bedding), the bottom 2-1/2" of the barrel rear (under the chamber/chamber reinforce), and at the tip of the forend (FE tip "up" pressure may vary, depending on bbl thickness/contour). The rifle I bought for a song turned a 10" grouper into a 1/2MOA shooter after the bedding was adjusted - it seemed that some well-meaning individual had tightly bedded the action & recoil lug everywhere. .
It ain't no fun, when the rabbit's got the gun
|
|
|
|
Joined: Jul 2009
Posts: 300
Campfire Member
|
OP
Campfire Member
Joined: Jul 2009
Posts: 300 |
[quote=RugerDude]
The rifle I bought for a song turned a 10" grouper into a 1/2MOA shooter after the bedding was adjusted - it seemed that some well-meaning individual had tightly bedded the action & recoil lug everywhere.
. This sounds like EXACTLY what i have going on. the action is bedded along the entire length and the lug is completely bedded. i may relieve the areas mentioned and see what happens. Thanks a bunch Nick
|
|
|
|
628 members (12344mag, 160user, 10gaugemag, 06hunter59, 16gage, 19rabbit52, 65 invisible),
2,823
guests, and
1,298
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,193,644
Posts18,512,394
Members74,010
|
Most Online11,491 Jul 7th, 2023
|
|
|
|